-
1 проверка
check (снк), test, inspection
- (раздел рэ) — adjustment/test
-, автономная (инерц. сист.) — self-testing
-, безвыборочная — random check
- биения (радиального) — check for /of/ eccentricity
- биения (скоса боковой поверхности, напр., колеса турбины) — check of swash. checking the swash of turbine wheel.
- введенных координат гпм — waypoint coordinate insertion /entry/ verification
- включения (работы) системы — system operational test
-, внерегламентная — unschedule maintenance check
проверки или осмотры самолета, его систем и агрегатов, проводимые в результате нарушения нормальных условий эксплуатации, независимо от утвержденных сроков проверок, производятся после грубых посадок, в случае удара молний в самолет, посадки с избыточным весом, столкновения с птицей и др. — those maintenance checks and inspection on the aircraft, its systems and units which are dictated by special or unusual conditions which are not related to the time limits. includes inspections and checks such as hard landing, turbulent air, lightning strike, overweight landing, bird strike
- встроенным контролем — built-in test
test the system by using its built-in test facility /ieature/.
-, выборочная — spot check, sampling inspection
-, выборочная (на работоспособность) — spot test
- гермокабины на герметичность — pressurized cabin leakage test
- готовности (ла) к полету — pre-flight check
"- заправки топливом" — fuel oty test (switch) (выключатель)
-, комплексная (систем) — combined systems checkout
-, контрольная — inspection check
- концентричности (колеса турбины, вала) — check of concentricity (of turbine wheel, shaft)
- координат места ла — aircraft position coordinate verification
- ламп — lamp test
- ламп табло (повторным включением) — annunciator lights recall. any reset annunciator lights can be recalled using the warning, caution and advisory lights test switch.
- межпопетная (перед обратным маршрутом) — turnround check
- методом "прокачек" (функциональная проверка электр. цепей) — functional test
- на выявление трещин (одним из объективных методов дефектоскопии) — inspection for cracks (by emplaying an objective method of inspection)
- на герметичность — leak test
-, наземная — ground check
-, наземная (с опробованием) — ground test
- на нспопнитепьном старте — lne-up check
- на магнитном дефектоскопе (на выявление трещин) — magnetic inspection (for cracks)
- на месте (без демонтажа изделия или агрегата с объекта) — in-situ check /test, inspection/. the on-condition check is normally an in-situ test.
- на оправке — check on mandrel
- на правильность формы и взаимного расположения поверхностей (детали) — test for truth
сюда относятся проверки на (не)плоскостность, (не)перпендикулярность, (не)параллельность, овальность и на правильность совмещения отверстий. — the methods for testing for form and alignment are used to check the flatness, squareness, angular relationship or parallelism of the part surfaces, the alignment of holes or the true circularity of round parts.
- на пробой изоляции — insulation breakdown test
- на работоспособность (для подтверждения нормальной работы изделия) — operational test. the procedure required to ascertain only that a system or unit is operable.
- на работоспособность (для подтверждения эксплуатационных характеристик) — operation test. то demonstrate the engine operational characteristics.
- (реакции двигателя) на сброс газа — deceleration test
- на слух — listening test
перебои в работе двигателя могут определяться проверкой на слух, — listening test is employed to determine the engine rough operation.
- на соответствие техническим условиям — functional test
проверка, проводимая с целью подтверждения, что система или агрегат работает в соответствии с минимально допустимыми ту. — the procedure required to ascertain that а system or unit is functioning in all aspects in accordance with minimum acceptable design specifications.
- на стоянке — ramp check /test, inspection/
simple test module provides rapid ramp check.
- на утечку (герметичность) — leak-test
- на утечку мыльной пеной — leak-test with soap suds арplied
coat the pipe with soap suds to detect leakage.
- наличия электрической цепи от...до... — check of electrical circuit between...and...for continuity
- нивелировки (заклинения) неподвижных поверхностей самолета — check of rigging of fixed surfaces
- огнетушителей (без разряда) — fire extinguisher test (firex
нажать кнопку проверка огнетушителей и в этом случае должны загораться лампы 1-я очередь и 2-я очередь срабатывания. — press the firex test button and all main and altn lights illuminate on fire extinguisher test panel.
-, перекрестная (напр., всех аналогичных приборов) — crosscheck (хснеск) crosscheck the three altimeters.
-, периодическая — periodic check
- пиропатронов (противопожарной системы) — squib test. repeat procedure with squib test switch in aft position.
- плоскостности детали на контрольной плите — check for flatness of a part surface against the face of a surface plate
для проведения данной проверки на поверхность кантрольной плиты наносится краска (берлинская лазурь), затем чистая проверяемая поверхность прижимается к контрольной плите. плоскостность проверяемой поверхности, оценивается no наличию отпечатков краски (на выступающих участках). — то make the test, smear the face of the surface plate with marking (consisting of prussian blue or redlead with oil), then wipe clean the sruface to be checked and rub it lightly on the surface plate. the truth of the surface can be estimated by the appearance of the transferred marking.
-, повторная — recheck
- под током /напряжением/ (оборудования, системы) — test /check/ of equipment energized, alive (equipment) test
- по налету — check by flight hour(s)
-по налету, регламентная — periodic /scheduled/ maintenance cheek by flight hour(s)
-, послемонтажная — post-installation check
-, послеполетная — post-flight check
- по состоянию (по мере надобности) — оn-condition check (ос)
профилактическое техническое обслуживание (контроль качества ремонта), выполняемое в виде периодических осмотров, проверок (или испытаний изделия (агрегата), на обнаружение механических дефектов (в доступных пределах) для определения допустимости дальнейшей эксппуатации изделия (до следующей проверки по состоянию). — а failure preventive primary maintenance (overhaul control) process which requires that the item be periodically inspected, checked or tested against some appropriate physical standards (wear or deterioration limits) to determine whether the item can continue its service (for another ос check interval).
- по техническому состоянию — оn-condition check
- по форме "а" ("в", "с"), регламентная (периодиче — scheduled (periodic) "а" ("в", "с") check
- правильности ввода данных — data entry /insertion/ verification
-, предварительная — preliminary check
-, предвзлетная (по контрольной карте) — pre-takeoff check, before-takeoff check
-, предполетная — pre-flight check
-, предпосадочная (по контрольной карте) — pre-landing check, beforelanding check
-, предстартовая — prestart procedure
- приемистости (двигателя) — acceleration test
- прилегания поверхностей на краску (берлинскую лазурь) — check of the surfaces for close contacting indicated by continuity of (prussian blue) marking transferred
-, принудительная (вводимая вручную) — manually initiated /induced/ test /check/
- противообледенительной системы (надпись) — anti-ice test
- противопожарной системы (надпись) — firex test
- работоспособности — operational test
- работы — operational test
- радиального биения (рабочего колеса турбины (на оправке) — check of eccentricity /concentricity/ of turbine wheel (on mandrel)
-, регламентная — scheduled maintenance check
проверки самолета, его систем и агрегатов в указанные сроки. — those manufacturer recommended check and inspections of the aircraft, its systems and units dictated by the time limits.
- самолетов парка, выборочная — sampling inspection of fleet
"- сигнальных ламп" (надпись) — lamp test
- системы — system test (sys tst)
- системы сигнализации пожаpa — fire warning) test
"- системы сигн. пож. в otc. дв. (надпись) — eng compt fire warn test
-, совместная (проводимая поставщиком и покупателем) — conjoint check, check or test conjointly conducted (by supplier and buyer)
- соконусности несущего винта (вертолета) — rotor blade tracking test
- сопротивления изоляции — insulation-resistance test
test for measuring ohmic resistance of insulation.
- с помощью встроенного контроля — built-in test
- с (к-л.) пульта (или наборного поля) — test /check/ via /from/ сапtrol panel (or keyboard)
-, стартовая — on line test
-, стендовая — bench test
-, стендовая (испытание) — bench check/test/
- технического состояния — operational status check, check for condition
-, транзитная — transit check
план транзитного полета включает транзитную проверку. — the transit time schedule includes transit check.
-, тщательная — thorough check
-, функциональная — functional test
- электрической прочности (изоляции) — (insulation) voltage-withstand test
проверка способности изоляции выдерживать (повышеннoe против нормы) напряжение. — application of voltage (higher than rated) for determining the adequancy of insulation materials against breakdown.
- элементов конструкции (ла), выборочная — structural sampling test
- эффективности системы охлаждения (двигателя и редуктора вертолета) при взлете (висении, наборе высоты, снижении) — takeoff (hovering, climb, descent) cooling test
'включение проверки' (надпись) — test on
причина п. — reason for check /test/
производить п. по 3, пп. a,6 — test the unit according to requirements of para. 3 (a, b)Русско-английский сборник авиационно-технических терминов > проверка
-
2 окончательная проверка
1) General subject: final check2) Agriculture: final control3) Construction: final revision (напр. чертежей, спецификаций и т.д.)4) Law: final examination5) Economy: final inspection6) Accounting: final review7) Oil: in-situ check (проверка на месте)8) Quality control: final check-outУниверсальный русско-английский словарь > окончательная проверка
-
3 на месте
1) General subject: and then, be out, (не на) in (out of) position, (чьём-л.) in (smb.'s) stead, in situ, on board (?), on the job, on the nail, on-the-spot, then and there, there and then, on-site, (происшествия) at the scene (A 17-year-old boy behind the wheel of a truck drove into the path of an oncoming minivan east of Calgary. The teenage driver and a couple, both 75, died at the scene.), on the ground (What is really happening on the ground in Zimbabwe? - Что же происходит на месте в Зимбабве?), onsite, insitu2) Naval: in pos3) Colloquial: on-the-scene4) Sports: stand fast5) Military: at the halt6) Engineering: in position, in-place, on-machine7) Mathematics: at the site, (своем) in position, (своем) on the site8) Religion: in situ (Latin for "in position", in the natural or original position or place)9) Railway term: home10) Economy: in loco11) Automobile industry: in situ (напр. о двигателе, ремонтируемом без снятия с шасси), on the site (установки), situ12) Architecture: in-situ13) Mining: situ in siting (залегания)15) Jargon: (прямо) on the premises16) Information technology: in place17) Oil: at the location (выполнения услуг, работ), on site (работ; залегания), on-scene18) Business: on the spot19) Drilling: in-house20) Quality control: (своём) in place -
4 осмотр
inspection
-, внеплановый — unscheduled maintenance inspection /check/
-, внешний — external inspection
-, внешний (в графе способ обнаружения дефекта) — visual inspection
-, внутренний — internal inspection
-, выборочный (проверка) — sampling /spot/ inspection
- для определения и устранения неисправностей — inspection for trouble shooting
-, ежедневный — daily inspection
- кабины экипажа — cockpit inspection
- кабины экипажа на готовность к полету (отсутствие опасных условий) — cockpit safety inspection. а cockpit safety inspection procedure is performed by the co-pilot to ascertain that electrical and/or pneumatic power may be applied safely.
-, комплексный (систем) — combined systems checkout
-, контрольный (ла, систем агрегатов при обслуживании) — inspection
-, контрольный (разобранных узлов двигателя после длительного испытания на выявление усталостных разрушений и/или износа) — teardown inspection after completing the endurаnce test the engine must be completely disassembled and а detailed inspection made of each part to check for fatigue and wear.
-, медицинский — medical examination
- на месте (без демонтажа) — (visual) in-situ inspection
-, наружный — visual inspection
-, наружный (для определения повреждений) — mechanical check
-, нерегулярный — irregulator inspection
-, окончательный — final inspection
-, оперативный — line inspection
-, периодический — periodic inspection
-, плановый — scheduled inspection
-, поверхностный — light inspection
- после грубой посадки — hard landing inspection
-, послеполетный — post-flight inspection
-, предполетный — pre-flight inspection
-, приемо-сдаточный — acceptance inspection
- /проверка/ (раздел рэ) — inspection/check
-, профилактический — (failure) preventive inspection
-, регламентный — scheduled maintenance inspection /check/
-, регламентный (25-часовой) — 25-hour inspection
-, случайный (нерегулярный, незапланированный) — haphazard inspection. irregular and haphazard inspection will invariably result in gradual and certain deterioration of the airplane.
-, стартовый — lineup inspection
-, текущий (оперативный) — line inspection
-, текущий (плановый) — routine inspection
-, технический — inspection
-, тщательный — through inspection
-, целевой (внерегламентный) — unscheduled inspection
- элементов конструкции (ла) — (aircraft) structural inspection
- элементов конструкции, выборочный ла — structural sampling inspection
выборочный осмотр сокращает трудозатраты, потребные для контроля состояния конструкции ла. — structural sampling (inspection) will reduce manhours required for the airframe structural inspection.
- элементов конструкции планера самолета — airframe structural inspection
-, эпизодический — irregular inspection, inspection at irregular intervals
акт о. — inspection report
маршрут наружного о. (самолета) (рис. 148) — circuit of external inspection, walk around check
порядок о. — inspection procedure
результаты о. — results of inspection
с момента последнего о. — since last inspection, from date of last inspection
подвергать 0. — subject to inspection, inspect
производить (внешний) о. — inspect (visually)Русско-английский сборник авиационно-технических терминов > осмотр
-
5 замер
measurement
(давления, температуры и т.п.) — measurements to check the symmetry are taken between tile reference points.
- (показание прибора) — indication, display
наличие жидкости в гидробаке замеряется при помощи поплавкового датчика, — the hydraulic tank contents indication is given by a floattype transmitter.
- в полете — inflight measurement
- в точке а — measurement at point a
- на месте (без демонтажа и установки дополнительных устройств) — in-situ measurement in-situ measurements cover parameters to be checked at points scattered all over the aircraft structure.
- температуры (напр. выходящих газов) посредством термопар — exhaust gas temperature measurement by thermocouples
точка 3. — measuring point
производить (один, два и т.д.) 3. (для проверки правильности показаний прибора) — take... readings of a measurement. always take two or three readings of a measurement because this will help to ensure that the instrument reading is correct.Русско-английский сборник авиационно-технических терминов > замер
-
6 внутрисхемный контроль
1) Engineering: in-circuit check, in-circuit testing, in-situ testing2) Electronics: in-circuit testУниверсальный русско-английский словарь > внутрисхемный контроль
См. также в других словарях:
India — /in dee euh/, n. 1. Hindi, Bharat. a republic in S Asia: a union comprising 25 states and 7 union territories; formerly a British colony; gained independence Aug. 15, 1947; became a republic within the Commonwealth of Nations Jan. 26, 1950.… … Universalium
Geotechnical investigation — Geotechnical investigations are performed by geotechnical engineers or engineering geologists to obtain information on the physical properties of soil and rock around a site to design earthworks and foundations for proposed structures and for… … Wikipedia
building construction — Techniques and industry involved in the assembly and erection of structures. Early humans built primarily for shelter, using simple methods. Building materials came from the land, and fabrication was dictated by the limits of the materials and… … Universalium
Melanoma — Classification and external resources A melanoma ICD 10 C43 … Wikipedia
LASIK — or Lasik ( laser assisted in situ keratomileusis ) is a type of refractive laser eye surgery performed by ophthalmologists for correcting myopia, hyperopia, and astigmatism. [ [http://www.intelihealth.com/IH/ihtIH/WSS/9339/32123.html LASIK. ]… … Wikipedia
Bongo (antelope) — The Bongo redirects here. For other uses, see Bongo (disambiguation). Western/Lowland Bongo Conservation status … Wikipedia
Flashline Mars Arctic Research Station — Flashline Mars Arctic Research Station … Wikipedia
Air Movement and Control Association — The Air Movement and Control Association International, Inc. (AMCA; pronounced Am Cah ) is a nonprofit organization that creates standards for, tests, and rates Heating, Ventilating, and Air Conditioning (HVAC) equipment. It is best known for its … Wikipedia
Siberian tiger — Conservation status Endangered ( … Wikipedia
Carcinogenesis — For the scientific journal, see Carcinogenesis (journal). Cancers are caused by a series of mutations. Each mutation alters the behavior of the cell somewhat. Carcinogenesis or oncogenesis is literally the creation of cancer. It is a process by… … Wikipedia
Genetic erosion — is a process whereby an already limited gene pool of an endangered species of plant or animal diminishes even more when individuals from the surviving population die off without getting a chance to meet and breed with others in their endangered… … Wikipedia